Return to JunFac Hardened Universal Shaft (120-155MM) 5mm Hole (1)
Sort By::
Page of 1


  0 of 0 people found the following review helpful:
 
4 of 5 very strong!! May 31, 2015
Reviewer: Anonymous Person from Meridian, ID United States  
These shafts are super strong. Half moon  style spline.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 shaft March 9, 2015
Reviewer: william goldsmith from rhoadesville, VA United States  
A good fit.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Excellent service July 21, 2014
Reviewer: caleb Huffman from Columbus, OH United States  
The quality of these are awesome. Bought these for my Axial wraith and they fit perfectly. They were shipped extremely fast. Great service

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 Drive Shafts for wraith May 2, 2014
Reviewer: Sam Rowand from Chilliwack, BC Canada  
These are very strong, tolerances are not as tight as the MIP. The slip shaft is not splined, it is 3/4 round with a flat spot. On the set I got the 5mm hole was not drilled deep enough for the wraiths tranny shaft. Had to shorten the tranny shaft a millimeter. For the price these are a great up grade. 5 months later still going strong.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Perfect fit for scx10 newbright jeep jk January 17, 2014
Reviewer: Curtis N from Barrie, ON Canada  
I extended my front end on my honch to fit the jk body without the spur gear rubbing the interior. These driveshafts fit both front and rear lengths perfectly. I was worried it might be a little too long to fit in the rear.

So far excellent performance.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 axial wraith twizzler shafts October 7, 2013
Reviewer: Anonymous Person from ct  
Kept twisting the stock shafts with my wraith and saw these on here.  Was skeptical about the fitment size but for the price of two you cant beat it.  Needless to say they bolted up perfectly on my stock wraith and used them in my comp over the weekend and they took a beating without any problems.  I would recommend these over the MIP shafts for two reasons.  Look better and not as expensive as the MIP's.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
4 of 5 Great value October 5, 2013
Reviewer: Jeff H. from Shoreview, MN United States  
I bought one of these for my Axial Wraith since this product came up when I searched for Wraith parts.  On one of the outdrives however, this shaft won't slide on far enough to get a set-screw pin through. I would have just ground down the output shaft a millimeter or drilled into the yoke a bit, but it fit well on the other outdrive, and so I just swapped it to the other side instead. I had this same problem with their TF2 size driveshafts on my TF2, so I know it's not an isolated incident. If they would drill the hole in their driveshaft yokes a millimeter or so deeper, it would help.  But they're the cheapest good quality shafts out there, I'll still buy more!

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
4 of 5 shafted! June 19, 2013
Reviewer: pete kauenhofen from Aylmer, ON Canada  
what's to say?? went brushless in my wraith, geared it down to crawl better, put a et of those super cool swamper boggers on, and guess what? started twisting those plastic drive shafts of! go figure! not any more! fit great, and look great too!

Was this review helpful to you?

   
 

Our Friends Say...