Home > Cars & Trucks > Rock Crawlers >

Vanquish Products Currie Portal F9 SCX10 II Rear Axle Black Anodized

Vanquish Products Currie Portal F9 SCX10 II Rear Axle Black Anodized
 
RPP Price: $249.99

STOCK STATUS:
Out of Stock


Free Shipping
Part Number: VPS08360
Qty:

Description
 
Currie F9 Portal Rear Axle for SCX10 II based vehicles

The F9 Portal axles create extreme amounts of ground clearance under the center of your axle, increasing the clearance by 1/2"+ (13mm). This provides the equivalent of a tire over 1 inch taller than what is on your vehicle. The advantage of the Vanquish Currie F9 Portals is the gear reduction inside the portal (1.67:1) which can be adjusted with optional gear sets (1.4:1 Overdrive*). By adding reduction at the portal, less torque is transferred through the other upstream components in the drivetrain. These axles are a direct replacement to any Axial AR44 axle, using all stock links.

These axles come with all parts needed to assemble a full front axle.

Features:
  • Portal box integrated into the rear housing for the most clearance at the axle ends possible and a more scale appearance
  • Gear reduction in the portal of 1.67:1 (18/30), Optional Overdrive Ratio* of 1.4:1 (20/28)
  • Included Vanquish AR44 machined gear set
  • Overall axle reduction of 6.26:1 with stock portal ratio
  • 13mm increase in ground clearance
  • Hex to hex width of 7.66 inches, only roughly 5mm wider than a stock AR44 axle with a narrow hex
  • Chromoly inner rear axle shafts are triple bearing supported
  • Chromoly stub shafts with 6mm design at the drive pin which tapers down to a 5mm thread for ultimate strength
  • Chromoly spool
  • Aluminum 12mm hex with set screw
  • Uses all SCX10-II linkage
  • Complete Fast Eddy Bearings kit
  • Licensed by Currie Enterprises
  • Comes with One Piece Bearing Retainers (Patent Pending)
  • Double shear shock mounts
  • Upper link mounts built into third member
  • Increased upper link clearance for more suspension up travel ability

Note:

Requires the use of a 350 SLW hub or greater on Vanquish 1.9 wheels, Incision wheels will require a #4 or greater. Other wheel manufacturers offsets will vary. Axles must be used in pairs, you cannot run a front portal axle without a rear and vice versa.

*Overdrive gear sets are recommended for use in the front axle only
Average Customer Review: Average Customer Review: 5 of 5 5 of 5 Total Reviews: 1 Write a review.

Recommended Accessories
Vanquish Products Currie Portal F9 SCX10 II Front Axle Black Anodized
RPP Price: $329.99

Add Free Shipping
Vanquish Products Currie Portal F9 SCX10 II Front Axle Black Anodized


  0 of 0 people found the following review helpful:
 
5 of 5 VP Quality January 18, 2021
Reviewer: Maxsdrc from Carlsbad, CA United States  
Amazing Parts!

Was this review helpful to you?


Browse for more products in the same category as this item:

Cars & Trucks > Rock Crawlers
Cars & Trucks > Rock Crawlers > Vehicle Components > Axles
Cars & Trucks > Rock Crawlers > Vehicle Components
Cars & Trucks > Rock Crawlers > Scale & Trail Parts
Cars & Trucks > Rock Crawlers > Scale & Trail Parts > Axial SCX10 II
Cars & Trucks > Rock Crawlers > Scale & Trail Parts > Axial Wraith 1.9
Cars & Trucks

Our Friends Say...